IR Light Pipes/IR Light Tube
Hexagonal Light Tube reflecting Laser Beam
Only certain manufactures can custom design Infrared Light Pipes,
Hollow Waveguides and Homogenizers. This is because these are tubes
lined with a highly polished infrared reflective coating of
Laser Gold, which can be applied thick enough to permit these tubes to be used in highly corrosive atmospheres.
Laser Black can be applied to certain parts of light pipes to absorb IR light (see
photonics). This is done to limit IR light to only certain areas of the pipe.
While most light pipes are produced with a round cross-section, light
pipes are not limited to this geometry. Square and hexagonal
cross-sections are used in special applications. Hexagonal pipes tend to
produce the most homogenized type of IR Light. The pipes do not need to
be straight. Bends in the pipe have little effect on efficiency.
Light tube with reflective material
Also known as a “tubular skylight” or “Tubular Daylighting Device”,
this is the oldest and most widespread type of light tube used for
daylighting. The concept was originally developed by the
ancient Egyptians. The first commercial reflector systems were
patented and
marketed in the 1850s by
Paul Emile Chappuis in
London, utilising various forms of angled
mirror designs. Chappuis Ltd’s reflectors were in continuous production until the
factory was destroyed in 1943.
[1] The concept was rediscovered and patented in 1986 by
Solatube International of Australia.
[2]
This system has been marketed for widespread residential and commercial
use. Other daylighting products are on the market under various generic
names, such as “SunScope”, “solar pipe”, “light pipe”, “light tube” and
“tubular skylight”.
A tube lined with highly
reflective material
leads the light rays through a building, starting from an
entrance-point located on its roof or one of its outer walls. A light
tube is not intended for imaging (in contrast to a
periscope,
for example), thus image distortions pose no problem and are in many
ways encouraged due to the reduction of “directional” light.
The entrance point usually comprises a
dome (
cupola), which has the function of collecting and reflecting as much
sunlight as possible into the tube. Many units also have directional “collectors”, “reflectors” or even
Fresnel lens devices that assist in collecting additional directional light down the tube.
A set-up in which a
laser cut acrylic panel
is arranged to redirect sunlight into a horizontally or vertically
orientated mirrored pipe, combined with a light spreading system with a
triangular arrangement of laser cut panels that spread the light into
the room, was developed at the
Queensland University of Technology in Brisbane.
[3] In 2003, Veronica Garcia Hansen,
Ken Yeang, and Ian Edmonds were awarded the
Far East Economic Review Innovation Award in bronze for this development.
[4][5]
Light transmission efficiency is greatest if the tube is short and
straight. In longer, angled, or flexible tubes, part of the light
intensity is lost. To minimize losses, a high reflectivity of the tube
lining is crucial; manufacturers claim reflectivities of their
materials, in the visible range, of up to almost 99.5 percent.
[6][7]
At the end point (the point of use), a diffuser spreads the light into the room.
To further optimize the use of solar light, a
heliostat
can be installed which tracks the movement of the sun, thereby
directing sunlight into the light tube at all times of the day as far as
the surroundings´ limitations allow, possibly with additional mirrors
or other reflective elements that influence the light path. The
heliostat can be set to capture
moonlight at night.
Optical fiber
Optical fibers are well known as
fiberscopes for imaging applications and as light guides for a wide range of
non-imaging applications.
In the latter context, they can also be used for daylighting: a solar
lighting system based on plastic optical fibers was in development at
Oak Ridge National Laboratory in 2004;
[8][9] the system was installed at the American Museum of Science and Energy, Tennessee, USA, in 2005,
[10] and brought to market the same year by the company Sunlight Direct.
[11][12] However, this system was taken off the market in 2009.
Optical fibers are also used in the
Bjork system sold by Parans Solar Lighting AB.
[13][14]
The optic fibers in this system are made of PMMA
(PolyMethylMethAcrylate) and sheated with Megolon, a halogen-free
thermoplastic resin. A system such as this, however, is quite expensive.
[15]
A similar system, but using optical fibers of glass, had earlier been under study in Japan.
[16]
In view of the usually small diameter of the fibers, an efficient daylighting set-up requires a
parabolic collector to track the sun and concentrate its light. Optical fibers intended for
light transport need to propagate as much light as possible within the core; in contrast, optical fibers intended for
light distribution are designed to let part of the light leak through their cladding.
[17]
Transparent hollow light guides
A
prism light guide was developed in 1981 by Lorne Whitehead, a physics professor at the
University of British Columbia[18][19] and has been used in solar lighting for both transport and distribution of light.
[20][21]
A large solar pipe based on the same principle has been set up in a
narrow courtyard of a 14-floor building of a Washington D.C. law firm in
2001,
[22][23][24][25][26] and a similar proposal has been made for London.
[27] A further system has been installed in Berlin.
[28]
The 3M company developed a system based on optical lighting film
[29] and developed the 3M light pipe,
[30]
which is a light guide designed to distribute light uniformly over its
length, with a thin film incorporating microscopic prisms,
[19] which has been marketed in connection with artificial light sources, e.g.
sulfur lamps.
In contrast to an optical fiber which has a solid core, a prism light
guide leads the light through air and is therefore referred to as
hollow light guide.
The project ARTHELIO,
[31][32]
partially funded by the European Commission, was an investigation in
years 1998 to 2000 into a system for adaptive mixing of solar and
artificial light, and which includes a
sulfur lamp, a
heliostat, and hollow light guides for light transport and distribution.
Disney has experimented in using
3D printing to print internal light guides for illuminated toys.
[33]
Fluorescence based system
In a system developed by Fluorosolar and the
University of Technology, Sydney, two
fluorescent polymer layers in a flat panel capture short wave sunlight, particularly
ultraviolet light,
generating red and green light, respectively, which is guided into the
interior of a building. There, the red and green light is mixed with
artificial blue light to yield white light, without infrared or
ultraviolet. This system, which collects light without requiring mobile
parts such as a heliostat or a parabolic collector, is intended to
transfer light to any place within a building.
[34][35][36]
By capturing ultraviolet the system can be especially effective on
bright but overcast days; this since ultraviolet is diminished less by
cloud cover than are the visible components of sunlight.
